1993 Custom Chuck Paine Design Cutter

Added 10 December, 2012

About this Sailboat:

“Esme” is a beautiful custom made sailboat.

Call for appointment to see this beauty. (# removed)

www.ses-y.com

Equipment on Board:

Galley
Technautics Refrigeration
Force 10 3 Burner Propane Stove w/Oven and (2) 10# Aluminium Tanks
Double SS Sink w/Freshwater Mixer
Raw Water Washdown

Electronics
ICOM M-56 VHF Radio 25 Watt At Nav Station
Sea Inc SSB At Nav Station
Seat Talk HF/SSB
Magnavox MX-100 B/W GPS
Garmin 478 Color Portable w/Charts
Datamarine Depth, Speedip
Autohelm 7000 w/Hydraulic RAM steering, rudder indicator
Autohelm Wind Indicator
Ritchie Compass

Electrical
5 GRP 27 12V AGM Batteries
Dedicated 8D Start Batteries
100 Amp Alternator
12000 Watt Heart Interface Charger/Inverter w/Monitoring At Nav Station
Various SHore Line Adapters
Phone/TV Connector
Voltage Refulator
110/120 30 Amp Shore Power Cord
Interface Monitor Panel
Load/Amp/Volt Gauges
2 Battery Switches
1 Emergency AGM

Deck & Hull
BULKHEADS

Cedar Striped Reinforced Epoxy Glued, Machine Fitted Where Visible
Hull Stiffness Augmented By Heavy Fiberglass Encased Wooden Longitudinal Engine Bed Stringers
HULL:

Plywood and Lumber Bonded Epoxy w/Non-Slip Surface
KEEL:

Intregrated Encased Lead Plated Filled Ballast Fiberglass Covered Keel
WET AREA & SIDES:

Cedar Stripped Planked COvered w/Fiber Enforced Expoxy
Transom Raked Aft and Rounded Wood Support Fiber Epoxy
Hull to Deck Has Overlapping Flange Construction w/Epoxy Fasteners Visibly Bedded In Marine GradeElectrometric Compounds
RAILS:

22 Stanchions 1″ SS w/Lifelines
Chain Locker is Accessible Thru-Bolted
SCUPPERS:

Decks Drain Overboard Via Molded Scupper
CHOCKS & CLEATS:

10″ Heavy Dut Cleat On Bow
(2) 10″ Cleats Mid-Shios
(2) 10″ Cleats Aft, thru-Bolted and Bedded
Bronze Ball Valve thru-Hulls w/Bronze Strainers
(2) Transducers STBD Mid-Ship
Safety Gear:

AVON Life Raft
EPIRB
Blipper-Type Radar Deflector
Safety Harness
Fire Extinguishers
Auto Halon In Engine Compartment
PFD’s
Flares
Fog Bell
Air Horn
Other Hull & Deck

ABI Mechanical Anchor Windlass, Capstan, Gypsy and Chain Stopper
Chain Locker, Double SS Bow Roller
35# CQR Plow
#3 Bruce
#30 Danforth Kedge
1/4″ Galvanized Chain on Rodes 200′ 5/8″ 3 Braid Nylon
Bimini, Dodger & Enclosure
Hatch Covers and Opening Ports
Allow Plenty of Light and Ventilation Below
All Bronze Thru-Hulls

Sails & Rigging
Extruded Aluminum Double Spreader Mast W/Internal Halyards
Deck Stepped To COmpressions Post Stepped To Keel
Aluminum Boom W/Internal Reefing
Outhaul & Downhaul
Cast Aluminum Gooseneck Attachments
SS thru-Bolted Chain plates Fully Wrapped Into Keel
Head and Backstays 3/8″ 1×19 SS Wire w/Turnbuckles and Swaged Terminals
Mack Sails
Full Batten Vertical Reefing Furling Main
Genoa On Harken Roller Furling
Staysail
Aluminum Whisker Pole
(2) #64 Harken ST Sheet Winches
(2) #42 Rigging WInches
(1) #32 Harken Rigging Winch
Running Rigging In Good Condition

Engine & Mechanical
3 Blade Variable Pitch bronze Propellor on 1 1/4″ SS Prop Shaft
4″ Wet Exhaust w/FRP Silencer
Raw Water Closed Cooling System
Heat Exchanger
100 Amp Alternator w/Adjustable regulator
Full Complement Of Engine Gauges
12V Shur Flo Fresh Water Pump
6 Gallon Water Heater


Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
Custom Chuck Paine Design Cutter
This is an archived listing. If you have any comments about this boat, corrections to the specifications listed, or can provide additional information or photos, please use the comment form below and share what you can. I will update information as it becomes available.

No Comments »

No comments yet.

Leave a Reply

Your email address will not be published. Required fields are marked *