RSS Feed

1992 Coast Cutter

19 October, 2012 by EVAN

About this Sailboat:

1992 Coast 34 Cutter

Builder: Coast
Designer: Shannon/Roberts
LOA: 34′ LWL: 28’4″
Beam: 11’6″
Displacement: 16,000
Draft: 5’5″ Ballast: 6,500lbs

The Coast 34 is a modern, high performance cruising boat based on the traditional Scottish fishing vessel.

“Hallie” is a offshore cabable cruiser. The Hull was laid in 1992 and the boat was finished and launched in 1997, and is very clean throughout. Powered by fully rebuilt Yanmar 3GM27 diesel.

Built as a production version of the Roberts 341 designed by Grahame Shannon of the Bruce Roberts Design Group.

Equipment on Board:

Engine: Rebuilt 3cyl Yanmar Diesel, 27 HP, Model 3GM27

Tankage: 30 gal fuel, 100 gal in two S/S tanks, & 30 gal holding tank.

Accomodations:
– 6’4″ Headroom
– New Dickinson Antarctic Diesel Heater (2012)
– Port Visors
– Lee Cloths (2009)
– New Full Enclosure (2011)

Galley/Head:
– Forced 10, 3 Burner Stove & Oven
– On Demand Hot Water
– New 12 volt LP system (2011)
– Fridge/Freezer, Top Loading w/new Compressor Diode (2012)
– Raritan PH 11 Head (2007)

Electronics:
– Standard Horizon CP 185
– Uniden VHF, w/Wireless Mic., both 25 watt
– Alpine CD-AM/FM Stereo, w/ 4 West Marine Pro Series 6.5″ speakers (2 in Cockpit & 2 in Cabin)
– Standard Horizon Depth Sounder
– Furuno Mast Mount Radar

Electrical:
– 4 Trogan T-105, 6 volt house bank
– New Xantrex 40-amp Battery Monitor (2010)

Deck:
– Muir Cougar Electic Anchor Windlass w/200′ chain & 150′ rode
– 45lb CQR Anchor
– Blue Sea winch covers, hatch covers w/bug screens, cockpit bag, & winch handle holders
– Bimini w/solid zip in, between dodger and bimini, that includes windows, screen zip in, helm cover & windlass cover
– New Full Canvas Cockpit Enclosure (2011)
– Custom stainless swim ladder
– Custom stainless hand rail from Stern to gates

Sails & Riggig:
– Full batten main sail w/lazy jacks & two reef points
– New 125% furling Genoa (Nov 2010)
– Furlex roller furling
– Stay Sail
– S/S self tailing winches
– Heavy duty aluminum alloy spars
– 1×19 SS rigging
– Deck stepped mast
– All lines lead aft
– ABI Staysail release for sloop rigged sailing
– Radar reflector

Additional:
– Fiberglass 5-gallon propane tank
– 3 caframo 12-volt fans
– Teak spice racks, paper towel holder, binocular rack, key rack,
– Replaced original settee table with teak folding table
– Cockpit table – fold down
– New bottom paint (Sept 2011)

Coast Cutter
Coast Cutter
Coast Cutter
Coast Cutter
Coast Cutter
I do my best to post the most accurate information I can find, but please be aware that information here may be incorrect. If you have any comments about this boat, corrections to the specifications listed, or can provide additional information or photos, please use the comment form below and share what you can. I will update information as it becomes available.

No Comments »

No comments yet.

Leave a Reply

Your email address will not be published. Required fields are marked *